How to Grow Cannabis Clones

A cannabis clone is a cutting from a fully-grown female marijuana plant. Being an identical genetic to a female plant, a clone guarantees it will thrive just like its mother. It can also mean the plant may carry any health issue that the mother shrub had. If you want to grow a clone someday, make sure you raise a healthy female cannabis first.

Important Facts to Know About Cannabis Clones

A clone goes through two cycles in its lifetime. These are the vegetative and flowering cycles. Throughout the vegetative cycle, the plant focuses on developing its foliage and roots. For this cycle, a clone should receive around eighteen hours of light plus six hours of dimness every day. If you don’t keep a clone in its vegetative growth phase for a long time, it may lead to pre-flowering.

A marijuana plant is photosensitive, which means it will flower when it receives too much dimness that can also cause stress on the plant. You should keep an eye on the plant throughout the early phase of its life. Also, watch out for the indications of heat stress like curling or drooping leaves.

If the plant shows any symptoms of stress, then give it a break and transfer it back to where shade is available. You may also continue giving supplemental lighting over the dim cycle of the day to ensure the plant will receive the adequate length of darkness.

The plant’s flowering phase is the time it receives around twelve hours of light and another twelve hours of dimness. If you plant the clone outdoors, the plant needs a trigger, so it can flip to the flowering cycle.

Cloning your marijuana plants is cost-efficient and will provide you with a completely sustainable harvest. It is not hard to clone a marijuana plant. But, the job is boring. Here are some tips and hints on how you can successfully grow your clone:

  • In cloning a plant, you need a razor to cut the main steam. Likewise, prepare some water, rooting medium, and a rooting hormone. Wipe the trays, blades, scissors, prop dome, and cutting board with a gentle bleach solution and rinse them well. Make sure the mother plant you want to clone is healthy. The healthier the mother, the sturdier the clone. Give it a try and wait for 60 days before taking a part of the plant.
  • Ensure you have a good growing area for a clone. There should be proper ventilation, a systematic source of light, room for the plant, and other necessities. In growing a new batch of newly created clones, keep them in a little nursery where the plants will stay apart from the mature plants. This way, you can easily give them the attention they need.
  • When taking a clone, find the healthier and sturdier lower branches. The clone must be between 8 and 12 inches long. Make sure your rooting stimulator is ready to dip the clone into.
  • Put the freshly cut part of the mother plant in the water after you remove it from the rooting stimulator. Make sure there are no bubbles because they are the leading clone killers. There should be enough water for the clone to survive. If there are more bubbles on the water, the clone may not be able to soak up water.
  • Ensure as well that you slide the treated part of the clone in the rooting pellet or plug as faster as you can. A comfy fit to the treated stem is important. The clone won’t stick and take in moisture sometimes. You will be losing your clone when that happens. It will weaken and die.
  • A clone is more sensitive than a mature plant. Be sure you watch over it throughout the first seven to 10 days. That is a too critical period for a clone.
  • Try to finish the job as soon as possible. You need to be efficient because a clone is different from a seed. It tends to grow faster so be sure you have the needed supplies ready to maintain your clone.
  • Keep the growing area clean. A clone is weaker and more susceptible to disease and bacteria. Ensure that the root is growing in healthy and clean soil.
  • Keep an eye on your ventilation system, too. Make sure it gives minimal to zero breezes. Excessive breeze can cause drying of the clone while too minimal breeze can keep the air stagnant that makes your clone vulnerable to pests and bacteria.
  • Likewise, you don’t need to spray your clone with water. But, if you want to do it, make sure the water you use is just right. Spray enough water once every 3 days to prevent excessive moisture.
  • A clone needs a specific volume of light and minerals due to its sensitivity. Make sure you know more about a clone to ensure your success.

How to Store a Clone Temporarily

Ideally, you must plant a clone right away after getting it from the mother plant. You should prepare the space beforehand and store the clone temporarily before you transplant it. Here are some tips to help you out:

  • Water the clone with a diluted nutrient formula and put it under a low-intensity light bulb. You can use either T12 or T8 bulb. Avoid using a T5 bulb as it can cause your clone to start stretching in advance.
  • Make sure you the cubes are always moist but avoid allowing the standing to gather inside the tray. It will control the growth rate of your clone, helping you keep it in a manageable and ideal size.
  • When your clone starts to stretch, make sure that you rearrange it to keep it apart from other clones you have. Also, you must transplant the clone as quickly as possible.

What Can Happen After Transplanting the Clone?

For the first 2 weeks, you must check the humidity of the rockwool cube. Pour a cup of water on the cube when necessary. This will help the cloned plant grow a sturdier root system.